Ok, Everyone in the US carries the same ones. Meaning they are the same hardness. The way to tell is the center is purple and the outer part is black. As for PF making a harder version, YES they do be WMW is the only that has ever ordered any, but we haven't recieved them yet. Since they had the fire and all. But we had ordered them to do some testing. We think they are going to be a great RACE Version. I think they will be too hard for street use, but we won't know until we have them in our hands. I'll let you know as soon as we finish testing.
As for the Motorsport part you see listed, that is a fancy screw with a big washer that is suppose to go at the back of the control. I have a few sets, but I personally will tell you that I don't think that washer is going to do anything since there isn't any reward force on the bushing.
Page 12 of 13
-
Way Motor Works New Member
-
andyroo New MemberMotoring Alliance Sponsor
- Sep 8, 2009
- 6
- water science and mapping, and suspesnion and brak
- Ratings:
- +6 / 0 / -0
so there is no "soft" version? just normal and race?
this board kicks ass. :lol: -
Steve AdministratorStaff Member Articles Moderator
Thanks for the info Way.
-
Way Motor Works New Member
-
Bushings come in pre-determined durometers (measured hardness) from Powerflex to work best in each particular location. If you feel you need a softer or harder compound to suite your particular needs and the option is not available, contact us. We can custom order in durometers ranging from 70A(Yellow), 80A(Purple), and 95A(Black). 70A is slightly harder than rubber and works great for drivers looking for a slight increase in chassis response. 70A is not suggested in certain location due to its lack of rigidity. 80A is noticeably harder than rubber and makes a great performance street material that retails low levels of NVH. 95A is the hardest, and can be used in certain locations with minimal NVH. For most locations, 95A is used for aggressive/track use only. Custom durometer bushing sets take at least 4 weeks for delivery.
Regards,
[email protected] -
-
Way Motor Works New Member
I think most of our stock order was in that HOT new blend. We had some of the standard bushing sets and the Hard black durometer being special made for us.
-
Steve AdministratorStaff Member Articles Moderator
-
this is a bit off topic
if they do custom durometers what about a new upper rear brushing.
I hear the stock is very soft and the madness is too hard for street.
just a thought, back to the thread.
-Jonathan
edit: fix poor grammar and spelling -
Update on fire
-
andyroo New MemberMotoring Alliance Sponsor
- Sep 8, 2009
- 6
- water science and mapping, and suspesnion and brak
- Ratings:
- +6 / 0 / -0
-
Way Motor Works New Member
We actually have already talked to PF about making those rear bushings for us, but it will take them a little while to get them designed.
Also I do have the control arm bushings in stock, we are the last in the US with any, I just hope my supply will last until we get our next batch, but don't think it will. If you are wanting them call me ASAP. -
-
My powerflex Bushings were in stalled at 40,000, now with 96.000, they are perfect, i cleaned them and used a lil of the lube sent with my h sport bars, They are are tight as the day i installed them,
The car has been tracked, Drove in frezzing wyoming winters.
Very Impressed with POWERFLEX
I did install the Madness bushing on my rearshocks whie installing my koni yellows, I felt it got rid of the high frequency bounce in the rear, The Foamish factory bushing were super soft
Give em 3 thumbs up........oh wait that isn't a thumb
-
Steve AdministratorStaff Member Articles Moderator
Any word on PF's recovery from the big fire? Are they fully back in business and keeping up with product shipment again?
-
Detroit Tuned Well-Known MemberMotoring Alliance Founding Sponsor
They are back in stock, any good vendor has them again. give us a call.
-
Just out of curiosity, where would the excess tire wear be seen with shot bushings? I'm 99% sure my front control arm bushings are shot to hell since the wheels move when I kick them, but I've been noticing some extra wear on the outer edge of the tires.
-
Detroit Tuned Well-Known MemberMotoring Alliance Founding Sponsor
the front tires. all based on alignment and tire pressures. do a hard shift from first to second, if you hear a loud clunk, the bushings are shot. or a less fun way is to tq. your lugs and if the wheel moves, but the body doesn't they are shot.
Chad
Detroit Tuned -
I wouldn't say its a loud clunk. But there is a noticeable click, I guess, on initial acceleration and abrupt deceleration.
You've got a pretty big order coming from me in the next few weeks, Chad.
Page 12 of 13