1st Gen JCW Most liked posts in thread: Tune and P1685 Code

  1. Whine not Walnuts

    Whine not Walnuts Active Member

    Mar 14, 2017
    359
    253
    43
    waitin for my check
    Fuquay Varina, NC
    Ratings:
    +338 / 0 / -0
    #2 Whine not Walnuts, Mar 16, 2017
    From what I have found on the web, P1685 has a primary sequence of (TQ_MAX_CLU_MON) with a parameter of 220 to 250 nm. The secondary sequence is (LV_TQ_MON_ACT_MON) . The monitor length/frequency of checks is 0.24/0.04 seconds.

    I have not heard anything from Jan. I am wondering if this is more tune related than software/hardware.
     
  2. Dave.0

    Dave.0 Helix & RMW Powered
    Lifetime Supporter

    May 4, 2009
    25,021
    13,497
    113
    Burbs of Philly, PA
    Ratings:
    +14,644 / 10 / -4
    #3 Dave.0, Mar 16, 2017
    Have you called Jan and asked him? (949) 464- 7691 (RMW1)
     
  3. Whine not Walnuts

    Whine not Walnuts Active Member

    Mar 14, 2017
    359
    253
    43
    waitin for my check
    Fuquay Varina, NC
    Ratings:
    +338 / 0 / -0
    #4 Whine not Walnuts, Mar 16, 2017
    Last edited: Mar 16, 2017
    Yes both calls and emails. He has been working with me through the issue.
     
  4. MCS02

    MCS02 Moderator
    Staff Member Articles Moderator Supporting Member

    Jul 31, 2009
    11,305
    6,277
    113
    Male
    Ratings:
    +8,070 / 10 / -3
    #5 MCS02, Mar 16, 2017
    Welcome to MA!
     
  5. Whine not Walnuts

    Whine not Walnuts Active Member

    Mar 14, 2017
    359
    253
    43
    waitin for my check
    Fuquay Varina, NC
    Ratings:
    +338 / 0 / -0
    #6 Whine not Walnuts, Mar 17, 2017
    Got Tune.03 from Jan today. So far so good. Keeping fingers crossed that the third time is the charm.
     
  6. Dave.0

    Dave.0 Helix & RMW Powered
    Lifetime Supporter

    May 4, 2009
    25,021
    13,497
    113
    Burbs of Philly, PA
    Ratings:
    +14,644 / 10 / -4
    #7 Dave.0, Mar 17, 2017
    Good luck, hope it all works out. Jan is the man to fix your tune issues if it's the tune and not a part issue.
     
  7. Whine not Walnuts

    Whine not Walnuts Active Member

    Mar 14, 2017
    359
    253
    43
    waitin for my check
    Fuquay Varina, NC
    Ratings:
    +338 / 0 / -0
    #8 Whine not Walnuts, Mar 26, 2017
    The 3rd tune increased the idle to about 1,000 rpms. Engine pulls well, 4500 to redline is sweet. The Dominator cam adds a nice low end rumble. Had a buddy in the car earlier in the week, neither of us are too small, and he was quite surprised at how well the car pulled.

    Have not driven a Gen2 or 3 JCW but from past cars, it is really close to the s2000s that I had that were 240 BHP. Quite satisfied with the results.

    Jan/RMW is the Gen1 Mod God.