Most liked posts in thread: What did you do with your MINI today?

Put a new adhesive speed enhancer on it.

 

Finally finished getting the Clubman back together, changed the oil and filter, took the bra out of storage and after an hour had it fitting and looking pretty good.
My friend that pasted and left me the Mini named it "Tinker", so tomorrow Tinker and I are heading to the Coast...taking the long route both down and back.

 

LOVE the new tires on my R50...so much that I'm putting another set on my R50 next week! What a difference in the ride and cornering!!

The '06 cup holder is on the R50 now. No longer do I have to live in fear of my wife spilling her beverage when she is with me in the R50 and I am driving!:ihih:

 

Both Wolfgang, the JCW and Tiki ali'i are ready to go to tomorrows Spring Fling run with DCMM. BOth cars fully washed, detailed, spic n' span...until the rain tomorrow.

 

Stoped down at Helix today to see friends before the Dragon and talk with JAN at RMW dyno tune day.

Also upgraded my pulley to a 17% with a new 532 belt. I am not worried about heat since I run 100% Meth.

Ready for the Dragon. :devil:

 

We looked at it on the dyno and the tq numbers gave a nice bump in the lower end, early in the powerband and HP dropped off a tiny amount at the high end at 7500 to 8000 rpm so it was nothing to worry about.

Yeah, with my custom tune I do not have a rev limiter set at OEM spec any longer. :devil:

Hp may have only dropped a few but Torque shot up nicely which was needed because the new OS GIKEN lsd is a true locker unlike the OEM lsd. More lowend tq is needed and when you have it it makes the car feel like it trying to pull up the asphalt because it has so much grip. :devil:

 

Made a run over to Esoteric Car Care last Thursday....

Todd Cooperider was just finishing up with making a product video in the showroom....

He came over and walked me through some questions I had... Really nice guy...

I picked up these...










Their shop car was parked out front....

 

Replaced both front wheel bearings. Was going to replace outer ball joints, but could not get the little bugg@rs to come out. On modmini's video they popped out like poop thru a goose. I should be so lucky. Soaked with PB Blaster, and will try during the week as I have to work 3rd shift tonight and it's close to nap time. All of this was in preparation for The Dragon, but might not be going now. Ceramic top on the stove has cracked, and "she who must be obeyed" is shopping for a new stove. :eek6: Then on Friday, it got cold at night and my wife noticed that the furnace was not blowing hot air. Guy came out yesterday (for $149 call out fee!!!!!!), and says that it might be the control panel. Guess we'll see how many body parts I have to sell to have that fixed.

 

MM I love Gyeon MOHS and topping it width the PolishAngel stuff.

 

You can get a drift down from the top and bang on them with a 3 pounder, they'll come out. Be sure to lube the new ones with some antiseize or grease so they'll just fall out the next time you need to change them

 

^^^^^ Yeah, going to get an aluminum drift from work tonight. PB should have had time to soak thru.

 

I think he meant that the ball joints are stuck in the hub after he got the bolts out - not that they won't come out of the lower control arm. At least I hope soo cause that's what my advice was based on!

 

Yeah, I have the tool to remove the ball joint from the control arm, but as Minidave says, it's stuck in the hub. Soaked overnight with PB, and now that I'm home from work, I'm going to attack it from the top with an aluminum drift and a BFH.

 

Finally finished fixing my frozen outside faucet. Now, I can wash my car...then wax my car...then detail the interior...and the list goes on and on.

 

Rebuilt the left trailing arm and brakes on the 89 Mini, trying to get ready for an upcoming run this Sat - which I think will be cancelled due to bad weather.